Lian Hup Electronics And Electric Sdn Bhd added 2 new photos in Arduino/MCU/Sensors
Oct 31, 2026 at 04:13 pm —
Tactile button Switch Push Button
Water Turbidity Sensor
Lian Hup Electronics And Electric Sdn Bhd added new photo in Arduino/MCU/Sensors
Oct 31, 2026 at 03:11 pm —
pH sensor PH Electrode Probe E-201-C PHS-25 PHS-3C Composite PH0-14 Analog Meter Sensor Module

pH sensor PH Electrode Probe E-201-C PHS-25 PHS-3C Composite PH0-14 Analog Meter Sensor Module

  Specification: Module Power : 5.00V Module Size : 43 x 32mm(1.69x1.26'') Measuring Range :0 - 14PH Measuring Temperature: 0 - 60 ¡æ Accuracy : ¡À 0.1pH (25 ¡æ) Response Time : ¡Ü 1min pH Sensor with BNC Connector pH2.0 Interface ( 3 foot patch ) Gain Adjustment Potentiometer Power Indicator LED   Sensor Board Pin Arduino Pin Description A (Signal) A1 (or A0) Analog voltage output representing pH levels + (VCC) 5V (or 3.3V) Main power supply input - (GND) GND Common power and signal ground BNC Jack pH Glass Probe Twist-lock coaxial connection to the electrode read more
Lian Hup Electronics And Electric Sdn Bhd added new photo
Oct 31, 2026 at 02:06 pm —
2.4 Inch 4 Inch TFT LCD Display Module

2.4 Inch 4 Inch TFT LCD Display Module

Arduino TFT LCD display shields vary across multiple sizes, mainly ranging from 2.4 inches to 4.0 inches. They differ significantly in communication protocols (Parallel vs. SPI), driver ICs, and pin overhead on development boards. A direct comparison of the key sizes helps evaluate project needs: A direct comparison of the key sizes helps evaluate project needs:   Feature 2.4-Inch Shield 3.5-Inch Shield 4.0-Inch Shield Typical Resolution 320x240 (QVGA) 480x320 480x320 or 480x320 (SPI/TN) Common Driver ICs ILI9341, SPFD5408, ST7789 ILI9486, ILI9488, ILI9481 ILI9486, ILI9488, ST7796S Interface Types 8-bit Parallel (Common) or SPI 8-bit Parallel or SPI SPI (Highly Preferred) or Parallel Pin Footprint Plugs directly onto UNO / Mega Direct plug-in shield style Shield layout or pin-out header panels These form factors serve as budget-friendly defaults for smaller user interfaces, frequently offering built-in MicroSD card slots. Interface: Uses an 8-bit parallel digital interface plus 4 control lines. Pin Overhead: Heavy pin load using digital pins 5–13 and analog 0–3 on Arduino boards. Compatibility: Plugs directly onto standard UNO boards; runs at half speed on Mega due to pin mapping changes.   Interface: 4-wire serial SPI communication. Pin Overhead: Saves significant microcontroller I/O pins compared to parallel options. Logic Levels: Safe built-in 3.3V / 5V logic compatibility. read more
Lian Hup Electronics And Electric Sdn Bhd added 2 new photos in Arduino/MCU/Sensors
Oct 31, 2026 at 11:14 am —
Gas Sensor Module - MQ2 MQ3 MQ4 MQ5 MQ5 MQ6 MQ7 MQ8 MQ9 MQ135
LORA SX-1278 433MHZ Wireless RA-02
Lian Hup Electronics And Electric Sdn Bhd added 2 new photos
Oct 2, 2026 at 05:06 pm —
REAN RCA Plug
HF 105F-4 AC Relay
Lian Hup Electronics And Electric Sdn Bhd added new photo in Audio Connectors
Oct 2, 2026 at 05:01 pm —
Lian Hup Electronics And Electric Sdn Bhd added 6 new photos in Relays
Oct 2, 2026 at 04:14 pm —
Lian Hup Electronics And Electric Sdn Bhd added new photo in Customised Cable
Jul 2, 2026 at 02:28 pm —
Lian Hup Electronics And Electric Sdn Bhd
Lian Hup Electronics And Electric Sdn Bhd added 7 new photos in Arduino/MCU/Sensors
Jun 15, 2026 at 10:07 am —
Lian Hup Electronics And Electric Sdn Bhd added new photo in Arduino/MCU/Sensors
Jun 13, 2026 at 01:51 pm —
TP-5100 Lithium Battery Charging Management System Module/

TP-5100 Lithium Battery Charging Management System Module/

Input Voltage Range: 5V to 15V DC (Absolute maximum up to 18V). Output Voltage: 4.2V (1S mode) or 8.4V (2S series mode). Maximum Charging Current: 2A (Adjustable via on-board sampling resistors). Charging Stages: 3-phase system (Trickle pre-charge ,Constant Current,  Constant Voltage). Built-in Protections: Over-current, under-voltage, over-temperature, short-circuit, and battery reverse polarity protection. Configuration & How to Use   1. Switching Between 1S (4.2V) and 2S (8.4V) Modes  The module features an on-board solder jumper labeled ''SET''. 1S Mode (4.2V default): Leave the SET pads open (un-soldered). Input voltage can be as low as 5V (e.g., standard USB). 2S Mode (8.4V): Short/solder the ''SET'' pads together. You must increase your input voltage to a minimum of 10V–12V (a 12V DC power adapter works perfectly). 2. Adjusting the Charging Current Most standard modules come pre-configured for the maximum 2A output using two 0.1¦¸ resistors in parallel. If you are charging smaller batteries (like a standard 18650 cell that shouldn't exceed 1A), you can desolder or swap out the current-sensing resistors (Rs): 0.1¦¸ resistor: Sets current to 1A. Two 0.1¦¸ resistors in parallel (0.05¦¸): Sets current to 2A. 3. Wiring Connections IN+ / IN-: Connect your input power source (5V for 1S, or 12V for 2S). BAT+ / BAT-: Connect directly to the positive and negative terminals of your battery pack. LED Header: Features three pads to solder an external, dual-color LED if you are mounting the board inside an enclosure. 4. LED Status Meanings Red LED On / Blue LED Off: Charging in progress. Blue (or Green) LED On / Red LED Off: Standby mode, fully charged, or no battery detected. 📌 Critical Working Notes No Internal Balancing: When using the TP5100 in 2S (8.4V) mode, it does not balance the two cells. It treats them as a single 8.4V block. If you are wiring two 18650 cells in series, you should ideally add a separate 2S BMS (Battery Management System) board between the charger and your batteries to ensure the cells stay balanced and safe. Heat Dissipation: While it runs cooler than linear modules, it can still get warm at a full 2A load. Ensure it has decent airflow if used continuously at maximum output. read more
next page